-
Defoamer Liquid LS880L
Product Description 1.High efficient foam preventer which can quickly eliminate the foam generated in the cement slurry. Good inhibitive and degassing effect. 2.Disperses well in the cement slurry, and inhibits foam from being produced by other additives. 3.Has minimal effect on other properties of cement slurry. Specifications Appearance Density,g/cm3 Water-Solubility Colorless or faint yellow transparent liquid 1.03±0.05 Dispersed in water Cement Slurry Pres... -
LH645L High Efficiency Spacer Additive Powder
Product Description 1.Spacer additive, which can remove drilling fluid effectively, is able to prevent cement slurry from blending with it. 2.Used below temperature of 120℃(248℉, BHCT). 3.Remarkable thickening effect and high viscosity with low-concentration. Good suspension effect on the weighing agent, insoluble solids and oil drops. 4.Good synergy performance can be used with other thickening agents. 5.Good thickening effect, suspending ability and stability. Easy to be dissolved and ... -
LH555L High Efficiency Spacer Additive Liquid
Product Description 1.Spacer additive, which can remove drilling fluid effectively, is able to prevent cement slurry from blending with it. 2.Used below temperature of 150℃(302℉, BHCT). 3.Remarkable thickening effect with high viscosity, good performance of suspension on weighing agent, insoluble solid and oil drop. 4.Slurries Compatibility test should be done before applying LH555L. 5.Direct application of LH555L is highly recommended as viscosity reduces drastically after being diluted... -
CA180L Compound Type and Non-phosphorus Washing Liquid
Product Description 1.Washing agent can effectively disperse and wash away the mud cake on the well wall, significantly increase the displacement efficiency and enhance cementaƟ on power between set cement and the wall. 2.Use below the temperature of 180℃(356℉, BHCT). 3.Compound washing liquid featured with non-phosphorus, non-toxic and low-foaming characteristics, mainly applied as washing and spacing agents during the process of oil well cementing where water-based drilling fluid is ap... -
SC440L MT RETARDER LIQUID
Product Description 1.Retarder helps extend the thickeningƟ me of cement slurry in order to keep it pumpable, which ensures sufficient pumping time for a safe cementing project. 2.Applicable for low-to-moderate temperature system, used below 90℃ (194℉, BHCT). 3.Mixed with water when applied, and water quality is not required. 4.When curing temperature is lower than bottom hole circulating temperature, strength of set cement at top may be affected. 5.The dosage of SC440L increases signifi... -
SC810 UHT POLYMER RETARDER
Product Description 1.SC810 is a ultra-high temperature polymer retarder, which helps extend the thickening time of cement slurry in order to keep it pumpable, and ensures sufficient pumping time for a safe cementing project. 2.Thickening time has a linear relation with the dosage and temperature. The Right-Angle thickening curve can be achieved. 3.Strength of set cement develops fast. 4.Use below 204.4℃ (400℉, BHCT). 5.Has good compatibility with polymer fluid loss additive, and little ... -
POLYMER RETARDER SC510 HT
Product Description 1.Retarder helps extend the thickening time of cement slurry in order to keep it pumpable, which, therefore, ensures sufficient pumping time for a safe cementing project. 2.Thickening time has a linear relation with the dosage and temperature. The Right-Angle thickening curve can be achieved. 3.Strength of set cement develops fast, and the top of the sealing section will not over-retarded. 4.Use below 150℃(302℉, BHCT). 5.Has good compatibility with polymer fluid loss ... -
Photoinitiator PI-0107 | 71868-10-5
Specification: Product code Photoinitiator PI-0107 Appearance White powder Density(g/cm3) 1.15 Molecular weight 279.398 Melting point(°C) 74-76 Boiling point(°C) 420.1 Flashing point(°C) 207.9 Absorption wavelength(nm) 231/307 Package 20KG/Carton Application Offset printing inks, flexo printing inks, screen printing inks, varnish, wood coatings, electronic materials, adhesives, plastic coatings. -
Photoinitiator TPOL-0210 | 84434-11-7
Specification: Product code Photoinitiator TPOL-0210 Appearance Light yellow viscous clarified liquid Density(g/cm3) 1.14 Molecular weight 316.33 Melting point(°C) 144.5-147 Boiling point(°C) 456 Flashing point(°C) 242.878 Absorption wavelength(nm) 273/370 Package 20KG/Carton Application Offset printing inks, flexo printing inks, screen printing inks, varnish, wood coatings, electronic materials, adhesives, plastic coatings. -
Crosslinker C-212 | 97-90-5 | Ethylene Glycol Dimethacrylate
Main Technical Index: Product Name Crosslinker C-212 Appearance Colorless transparent liquid Density(g/ml)(25°C) 1.051 Melting point(°C) -40 Boiling point(760mmHg) 260.6 Flash point(°C) 121.8 Solubility Slightly soluble in water. Property: 1.Ethylene glycol dimethacrylate is an organic compound that is a cross-linking agent. It is used in the manufacture of resins, coatings, adhesives, etc. 2.Diethylene glycol dimethyl propionate is a kind of double est... -
Crosslinker C-220 | 6291-95-8 | Trimethallyl isocyanurate
Main Technical Index: Product Name Crosslinker C-220 Appearance White or slightly Yellowish crystals Density(g/ml)(25°C) 1.097 Melting point(°C) 80-85 Boiling point(°C) 402.7 Acidity value(%) ≤0.5 Property: TMAIC is a white or yellowish crystal with very low homopolymerisation and highly thermally stable trifunctional monomers. Compared to other crosslinkers such as TAIC, its vapour pressure is low even at high temperatures and it is stable in water and i... -
Crosslinker C-135 | 101-37-1 | Triallyl cyanurate
Main Technical Index: Product Name Crosslinker C-135 Appearance Colorless transparent liquid or white crystals Density(g/ml)(25°C) 1.11 Melting point(°C) 26-28 Boiling point(°C) 156 Water solubility(20°C) 6g/L Flash point(℉) >230 Refractive index 1.529 Application: 1.TAC is used as a vulcanising agent for highly saturated rubbers, as a curing agent for unsaturated polyesters, and as a photosensitiser in the radiation crosslinking of polyolefins...
